yoppo (yoppo1026) 翻訳実績

5.0 146 件のレビュー
本人確認済み
13年以上前 女性
日本
日本語 (ネイティブ) 英語
医療 ビジネス エレクトロニクス 契約書 食べ物・レシピ・メニュー 旅行・観光 ジャーナリズム 漫画 文学 マニュアル
20 時間 / 週
お仕事を相談する(無料)
このユーザーにより翻訳された公開依頼の一覧です。この一覧には、完了されていない依頼は含まれません。
yoppo1026 日本語 → 英語
原文

段取り

切断現品票

スケールで寸法測定

切断現品票の寸法と材料寸法が合っているか確認する

スエージング早見表

加工品番表示

スエージング早見表で寸法確認

設備に加工寸法表示をする

専用治具で位置合わせ

専用治具を使いストッパーの位置合わせをする。

専用治具で位置合せ後の微調整可。

切断現品票とスエージング寸法早見表で寸法照合確認,材料寸法を測定する。

加工部の管内、及び外観に加工油が、付いている事を確認する(2本/ロット)

加工寸法をスケールにて、寸法確認する

寸法測定時に数値の読み間違いに注意する

翻訳

Setup

Cutting identification tag

Measure the dimension with a scale

Check whether the dimension of the cutting indentification tag corresponds with the dimension of the material.

Swaging chart

Processing part number display

Dimension check with the swaging chart

Display the processing dimension on the equipment.

Positioning with a dedicated jig

Use a dedicated jig to position the stopper.

Fine adjustment can be done after positioning with a dedicated jig.

Check the dimension using the cutting identification tag and the swaging dimension chart, and measure the dimension of the material.

Confirm that the inside of tube of processed portion and the appearance have processing oil (two/lot).

Measure the processing dimension with a scale.

Be careful of making mistakes when you read the value at measuring dimension.

yoppo1026 日本語 → 英語
原文

作業手順及び作業上のポイント

作業上注意

注意を守らないとこうなる

切断寸法の設定

現品票に基き、サイズ、材質を確認し入力設定をする

送りセットを切断長通りに入力する

切断本数の設定

現品票に基き、切断本数を確認する

切断本数を入力後日報に記入する

切断の開始

切断寸法・本数設定の再確認をする

マーク材、工程内不良が出た時に切断本数が少なくなってしまう 
切り込みキズが入ったまま流出する恐れがある

切断加工油はサンプレス油使用
オイルタンク内に1/2以上有ることを確認する
1回/1直確認

曲がりを確認する

翻訳

Work procedures and points of the work

Notice of work

If you don't follow the notice, it will become like this

Setting of cutting dimension

Based on the identification tag, check the size and material and do the input setting

Enter the feed set with the cutting length

Setting of cutting number

Based on the identification tag, confirm the cutting number

Enter the cutting number and fill in the daily report

Start cutting

Re-confirmation of the cutting size and the number setting

The cutting number will be less when there are mark materials and process failures.
The product might escape with a cutting line on it

Use Sun press oil as cutting process oil
Confirm that there is more than half in the oil tank
Once / 1 direct confirmation

Check the bend