スエージング部引きキズ・端面斜めを始め、終り１本／ロットに確認
加工品番、スエージング寸法の読み間違いに注意する。
加工品番を間違いなく掲示する
切断寸法不良の発生
切断未加工の発生
切断方向逆の発生
切断端面ナナメの発生
切断寸法不良の発生
指・手が切断される
切断寸法不良の流出
切断端面ナナメの流出
切断未加工の流出
カッターは回転させない
カッター刃に直角に当たる様に治具をセットする
カッター溝上に指･手を置かない
寸法をスケールにて測定後木型の基準線でＷチェック
基準線罫引き
パイプセット治具
試し切断
Rating
57
Translation / English
- Posted at 22 May 2015 at 10:51
Check the pulling scratch at swaging part/ slanting edge at the beginning and end, each time 1pc/lot
Be careful of misreading the processing part number and swaging dimension.
The processing part number shall be put without fail.
Occurrence of cutting dimension failure
Occurrence of unprocessed cutting
Occurrence of wrong cutting direction
Occurrence of slanting cutting edge
Occurrenec of cutting dimension failure
Cutting finger or hand
Escape of cutting dimension failure
Escape of slanting cutting edge
Escape of unprocessed cutting
Do not rotate the cutter
Set the jig so that it hit the cutter blade at a right angle
Do not put your fingers and hands on the cutter groove
After measuring the dimension with a scale, double check with the reference line of the wood pattern
Reference line ruling
Pipe set jig
Trial cutting
makuremagure likes this translation
Be careful of misreading the processing part number and swaging dimension.
The processing part number shall be put without fail.
Occurrence of cutting dimension failure
Occurrence of unprocessed cutting
Occurrence of wrong cutting direction
Occurrence of slanting cutting edge
Occurrenec of cutting dimension failure
Cutting finger or hand
Escape of cutting dimension failure
Escape of slanting cutting edge
Escape of unprocessed cutting
Do not rotate the cutter
Set the jig so that it hit the cutter blade at a right angle
Do not put your fingers and hands on the cutter groove
After measuring the dimension with a scale, double check with the reference line of the wood pattern
Reference line ruling
Pipe set jig
Trial cutting
Rating
50
Translation / English
- Posted at 22 May 2015 at 13:30
Began a swaging part argument scratch end face diagonally, and confirmation to end 1 / lot
Processing part number, note the misreading of swaging dimensions.
It will post without the processing part number mistake
Generation of cutting dimensions failure
Generation of cutting raw
Cutting direction opposite occurs
Occurrence of the cut end surface diagonal
Generation of cutting dimensions failure
Finger-hand is cut
Outflow of cutting dimensions failure
Outflow of the cut end surface diagonal
Outflow of cutting raw
Cutter is not rotated
And it sets the jig is like hitting the right angle to the cutter blade
Do not put your fingers, hands on the cutter groove
And W Check the dimensions measured after the wooden form of the reference line at the scale
Reference line ruling
Pipe set jig
Try cutting
Processing part number, note the misreading of swaging dimensions.
It will post without the processing part number mistake
Generation of cutting dimensions failure
Generation of cutting raw
Cutting direction opposite occurs
Occurrence of the cut end surface diagonal
Generation of cutting dimensions failure
Finger-hand is cut
Outflow of cutting dimensions failure
Outflow of the cut end surface diagonal
Outflow of cutting raw
Cutter is not rotated
And it sets the jig is like hitting the right angle to the cutter blade
Do not put your fingers, hands on the cutter groove
And W Check the dimensions measured after the wooden form of the reference line at the scale
Reference line ruling
Pipe set jig
Try cutting
翻訳ありがとうございました。
どういたしまして。
また機会がありましたらよろしくお願いいたします。