1.
添付の3番（Regulator）の接続口が大きく、ネジ加工もされていないので、造船所の銅管（φ10）を接続できません。
試しに接続してみたところ、接続口が大きく、銅管が抜けてしまいます。
接続方法をご教示ください。
2.
XX船においてフィルターの逆洗時（Back flush）にアラームが発生します。
マニュアルのチェック項目は確認し問題はありませんでした。海水も比較的きれいな海水です。
汚れの蓄積や詰まりが原因と推測します。
またこれとは別にアクチュエータから漏水があります。
評価
44
翻訳 / 英語
- 2017/05/22 13:22:01に投稿されました
1.
As the joint part of the third (Regulator) attached is too large and it does not have the thread, I cannot connect the copper pipe (φ10) of the shipyard.
I tried to connect it anyways, but I found the copper pipe was pulled off because the connect part is loo large.
Please tell me how to connect them.
2.
The alarm beeps on the ship XX during backflushing the filter.
I confirmed every item to be checked in the manual is fine. The sea water is also relatively clean.
I guess it is due to the dirt accumulation or the dirt clogging.
Apart form this, there is a liquid leakage from the actuator.
As the joint part of the third (Regulator) attached is too large and it does not have the thread, I cannot connect the copper pipe (φ10) of the shipyard.
I tried to connect it anyways, but I found the copper pipe was pulled off because the connect part is loo large.
Please tell me how to connect them.
2.
The alarm beeps on the ship XX during backflushing the filter.
I confirmed every item to be checked in the manual is fine. The sea water is also relatively clean.
I guess it is due to the dirt accumulation or the dirt clogging.
Apart form this, there is a liquid leakage from the actuator.
評価
50
翻訳 / 英語
- 2017/05/22 13:27:05に投稿されました
1. As joint of Number 3 attached (Regulator) is large and screw is not processed, I cannot connect copper pipe of the shipyard. I tried connecting it, and found that as the joint is large, the copper pipe is removed.
Please tell me how to connect it.
2. An alarm goes off when filter is back flushed in XX ship.
I checked the checking item in manual, and did not find a problem.
The water in the sea is relatively clean.
I guess that it might be caused by accumulation of dirt and it is stuffed.
Another cause might be leakage from accuator.
Please tell me how to connect it.
2. An alarm goes off when filter is back flushed in XX ship.
I checked the checking item in manual, and did not find a problem.
The water in the sea is relatively clean.
I guess that it might be caused by accumulation of dirt and it is stuffed.
Another cause might be leakage from accuator.
![[削除済みユーザ]](https://secure.gravatar.com/avatar/695023b4efd563721d13716b1457bc73.png?d=identicon&mode=crop&r=PG&s=42)
評価
50
翻訳 / 英語
- 2017/05/22 13:24:29に投稿されました
1. In the number 3 of the attachment, the connection is big and screw process has not done, so can't connect to a copper pipe of the shipyard.
When I tried to connect, the copper pipe fell out due to the big connection.
Please tell me how to connect?
2. The alarm occurs when we back flush the filter at xx ship company.
There is no problem in the checking steps on the manual. The sea water is clean. I assume this is because of accumulation of soil.
There are leaks from actuator sometimes as well.
When I tried to connect, the copper pipe fell out due to the big connection.
Please tell me how to connect?
2. The alarm occurs when we back flush the filter at xx ship company.
There is no problem in the checking steps on the manual. The sea water is clean. I assume this is because of accumulation of soil.
There are leaks from actuator sometimes as well.
