圧力計は0.065MPa を示していることがわかります。
ごくまれに、バルブから圧力計までの間でリークすることがあり、
その場合は添付写真に写っている赤いハンドルを開にすることで、
容器内部に充填されているN2の圧が圧力計に指示されます。
そこで0.035MPa以上に圧力計の指示が上がれば問題ありません。
上の作業で圧が上がらない場合、リークしている可能性があります。
圧力計の写真撮影及び、輸送時のダメージの有無の確認をお願いします。
漏れがあれば、漏れている箇所の写真もお願い致します。
Rating
50
Translation / English
- Posted at 24 May 2019 at 09:54
The pressure measure shows 0.065MPa.
Rarely, there is possibility of leaking from bulb to the pressure measure.
In that case, by opening the red handle in the attached image to the right, it shows on the pressure measurement N2's pressure filled inside the container.
Then if the indicator of pressure measure goes up to more than 0.035MPa, it is all right.
If the pressure does not goes higher, there is possibility of leaking.
Please check the pressure measure' photo shooting and if there was damage during shipping time.
If leaking, please take photos of the leaking place.
Rarely, there is possibility of leaking from bulb to the pressure measure.
In that case, by opening the red handle in the attached image to the right, it shows on the pressure measurement N2's pressure filled inside the container.
Then if the indicator of pressure measure goes up to more than 0.035MPa, it is all right.
If the pressure does not goes higher, there is possibility of leaking.
Please check the pressure measure' photo shooting and if there was damage during shipping time.
If leaking, please take photos of the leaking place.
Rating
50
Translation / English
- Posted at 24 May 2019 at 09:53
You can see the pressure gauge shows 0.065MPa.
Very rarely, a leakage may occur between the valve and the pressure gauge.
And in such case the N2 pressure filled inside the container is shown on the pressure gauge by opening the red handle in the attached picture.
If the pressure gauge shows the value over 0.035MPa, there should be no problem.
If the above process does not help to increase the pressure, a leakage could be the cause.
Please take the picture of the pressure gauge and confirm to see if there is any damage caused during the transportation.
Send me the pictures where the leakages are if any, too.
Very rarely, a leakage may occur between the valve and the pressure gauge.
And in such case the N2 pressure filled inside the container is shown on the pressure gauge by opening the red handle in the attached picture.
If the pressure gauge shows the value over 0.035MPa, there should be no problem.
If the above process does not help to increase the pressure, a leakage could be the cause.
Please take the picture of the pressure gauge and confirm to see if there is any damage caused during the transportation.
Send me the pictures where the leakages are if any, too.
Rating
50
Translation / English
- Posted at 24 May 2019 at 09:54
I understand that pressure gauge shows 0.065MPa.
Leaking appears between valve and the pressure gauge in few cases.
In that case, pressure of N2 filled in the container is shown in the pressure gauge by opening red handle in the attached photo. If the pressure gauge goes up more than 0.035MPa, there is no problem.
If the pressure does not go up by above work, it might be leaking.
Please check taking picture of the pressure gauge and if it is damaged during its transportation. If it leaks, would you take a picture of the leaking part?
Leaking appears between valve and the pressure gauge in few cases.
In that case, pressure of N2 filled in the container is shown in the pressure gauge by opening red handle in the attached photo. If the pressure gauge goes up more than 0.035MPa, there is no problem.
If the pressure does not go up by above work, it might be leaking.
Please check taking picture of the pressure gauge and if it is damaged during its transportation. If it leaks, would you take a picture of the leaking part?
![[deleted user]](https://secure.gravatar.com/avatar/695023b4efd563721d13716b1457bc73.png?d=identicon&mode=crop&r=PG&s=42)
Rating
52
Translation / English
- Posted at 24 May 2019 at 09:53
The pressure gauge shows the 0.065MPa now.
Rarely it may confirm the leakage between the bulb and metre.
In that case, for the instruction, set to OPEN by the red handle shown on the attached photo,
the pressure at N2 vacuumed in the container inside will be shown.
It you confirm that more than 0.035MPa on the pressure gauge, it will be no problem.
Unless you cannot get such pressure if you try above instruction, there might be chance of leakage.
Please send your the photo of pressure gauge along with damage while it it delivering if there might be.
If you confirm the leakage, also for the photo of leakage, please.
Rarely it may confirm the leakage between the bulb and metre.
In that case, for the instruction, set to OPEN by the red handle shown on the attached photo,
the pressure at N2 vacuumed in the container inside will be shown.
It you confirm that more than 0.035MPa on the pressure gauge, it will be no problem.
Unless you cannot get such pressure if you try above instruction, there might be chance of leakage.
Please send your the photo of pressure gauge along with damage while it it delivering if there might be.
If you confirm the leakage, also for the photo of leakage, please.
