使用方法
ケースを使用する際は必ず浸水しないかテストしてください
1･背面レンズとレンズ窓を合わせる
スマートフォンの上部両端部分を
隙間なく押し込む
2･ケースマリンの下段右を指で掴み片側のみを
引っ張り装着する
掴むときに爪を立てないで下さい
3･下段左端も同じように指で掴み
無理なく引き寄せ被せる
Rating
44
Translation / English
- Posted at 18 Jul 2012 at 16:23
How to use
When using the case, please ensure whether its not wet or submersed
1.Fit a rear lens and window lens together-
and tuck without gaps both ends of the upper part of the smartphone
2.Grasp the finger to the only one right side of two lower-case Marin
Mount using a tension
While grabing the claw please do not stand
3. Grasp the finger in the same way to the lower left edge
Cover reasonably drawn
miyami likes this translation
When using the case, please ensure whether its not wet or submersed
1.Fit a rear lens and window lens together-
and tuck without gaps both ends of the upper part of the smartphone
2.Grasp the finger to the only one right side of two lower-case Marin
Mount using a tension
While grabing the claw please do not stand
3. Grasp the finger in the same way to the lower left edge
Cover reasonably drawn
Rating
57
Translation / English
- Posted at 18 Jul 2012 at 16:41
Instruction to use
Before using the case, make sure to test it to ensure there is no inundation.
1･Match backside lens and lens window.
Insert both top corners of the smart phone making sure there is no gap.
2･Using figure, pull one side of the bottom right of the case marine to mount.
Be careful not to scratch it with nails.
3･Pull bottom left corner similarly.
Pull it naturally to cover.
miyami likes this translation
Before using the case, make sure to test it to ensure there is no inundation.
1･Match backside lens and lens window.
Insert both top corners of the smart phone making sure there is no gap.
2･Using figure, pull one side of the bottom right of the case marine to mount.
Be careful not to scratch it with nails.
3･Pull bottom left corner similarly.
Pull it naturally to cover.
4･前面液晶部分と後面カメラを合わせて
ケースマリンの位置を合わせる
5･スマートフォン投入口を整え全体に
なじませてから防水シールを上から
下にカメラをふさがない様に注意して貼る
防水シール装着後スマートフォンと防水が
密着するように指でなぞる
6･前面液晶保護フィルム、後面フィルムを
外したら準備完了です
Rating
57
Translation / English
- Posted at 18 Jul 2012 at 16:47
4･Adjust case marine position by matching front display area and back side camera area.
5･Paste water resistant protection tape before cleaning smartphone insertion point.
Make sure the protection sheet do not block the camera.
Press the sheet using figure to make sure smart phone and water resistant taping is coherent.
6･Ready to use after removing front display protection film and back side film.
miyami likes this translation
5･Paste water resistant protection tape before cleaning smartphone insertion point.
Make sure the protection sheet do not block the camera.
Press the sheet using figure to make sure smart phone and water resistant taping is coherent.
6･Ready to use after removing front display protection film and back side film.
Rating
50
Translation / English
- Posted at 18 Jul 2012 at 17:44
4. Adjust fit to ensure clear view of front screen and rear camera window.
5. Carefully apply the waterproof seal from top to bottom.
Ensure the inserting hole is completely covered and not obstructing the camera lens.
Check and rub seal contact to eliminate any air bubbles.
6. Remove front screen protector and rear protector.
Now the phone is fully dust&waterproof, whilst retaining full phone functionality.
5. Carefully apply the waterproof seal from top to bottom.
Ensure the inserting hole is completely covered and not obstructing the camera lens.
Check and rub seal contact to eliminate any air bubbles.
6. Remove front screen protector and rear protector.
Now the phone is fully dust&waterproof, whilst retaining full phone functionality.
