AからBが取り外せないとのことですが、対処法としてBossに潤滑油を垂らしながら六角レンチでBをゆっくり回してください。それでも外れない場合は、恐らくボルトが齧ってしまっていると思います。
液体窒素をBossにかけてください。Bossが冷気で収縮するので外れるかもしれません。
または、Bを壊して無理やり外してください。
齧っている場合、ネジ山はもう駄目になっているので、修正は難しい状況です。
新しくAを作るか、ネジ穴を完全に埋めて使ってください。使用上は問題無いと考えています。
評価
55
ネイティブ
翻訳 / 英語
- 2022/12/28 10:43:45に投稿されました
B cannot be taken from A, however. as a method of disposal, please drip lubricant on the Boss while slowly rotating a hexagonal wrench. If it still doesn't work, I think the bolt has probably eaten through..
Please pour liquid nitrogen on the Boss. The cold air will make the Boss shrink so you can take it out, maybe.
Also, please don't destroy B just to take it out by force.
If it has eaten through, a screw thread won't work so repair will be difficult.
Please make a new A or bury it completely in the screw hole before using. After using, I think you shouldn't have any problems.
Please pour liquid nitrogen on the Boss. The cold air will make the Boss shrink so you can take it out, maybe.
Also, please don't destroy B just to take it out by force.
If it has eaten through, a screw thread won't work so repair will be difficult.
Please make a new A or bury it completely in the screw hole before using. After using, I think you shouldn't have any problems.
評価
52
翻訳 / 英語
- 2022/12/28 18:54:31に投稿されました
You are saying that B cannot be removed from A, as a measure, please apply lubricant a bit to Boss and turn B slowly I'm by using a hex wrench.
If it can't still work, perhaps the bolt seems to be worn out.
Please apply liquid nitrogen over to Boss. Then, Boss is to shrink by the chill and it may become loosened.
Or, please try to remove it by forcing it to break B and remove it.
If it is worn out, the screwthread is broken.
The amendment seems to be impossible.
You should make A from the beginning or fill the screw hole completely, it has no practical problem when in use.
If it can't still work, perhaps the bolt seems to be worn out.
Please apply liquid nitrogen over to Boss. Then, Boss is to shrink by the chill and it may become loosened.
Or, please try to remove it by forcing it to break B and remove it.
If it is worn out, the screwthread is broken.
The amendment seems to be impossible.
You should make A from the beginning or fill the screw hole completely, it has no practical problem when in use.
評価
50
翻訳 / 英語
- 2022/12/28 10:50:18に投稿されました
I understand that you were not able to remove B from A. As a solution, please slowly rotate B with a hex wrench by dripping a smoother into the Boss. If it does not come off still, I would assume the bolt is stuck.
Please add the liquid nitrogen over the Boss. It might help the Boss shrink with the cold air to come off.
Or break B with forth to remove it.
If it is stuck, the screw thread is already useless, so it is difficult to fix.
Please newly create A or fill up the screw hole to use. I don't think there should be any problem for using it.
Please add the liquid nitrogen over the Boss. It might help the Boss shrink with the cold air to come off.
Or break B with forth to remove it.
If it is stuck, the screw thread is already useless, so it is difficult to fix.
Please newly create A or fill up the screw hole to use. I don't think there should be any problem for using it.
