装置に不具合が発生しています。
排水をするときに下記アラームが発生します。
（アラーム）
不具合状況：
1. 排水を始める前の暖機運転の際、ランプの出力が20kwまでしか上がらず、アラームが発生。
2. アラーム発生後、ランプの出力が0kwと表示されるので、"終了”をクリックし、運転を終了させる。
これを2,3回繰り返すと、ランプの出力が40kwまで上がり、通常通り使用できるようになります。
何か対処法があればお知らせください。
評価
50
翻訳 / 英語
- 2018/06/12 13:12:37に投稿されました
A problem is happening at device.
The alarm listed below goes off when I remove water.
(Alarm)
1. When I warm the device before start of removing the water, output of lamp goes up only to 20 kilowatts, and the alarm goes off.
2. After the alarm goes off, the output of the lamp is shown "0 kilowatt". Then I click "end" and stop operation.
If I repeat above 2 to 3 times, the output of the lamp goes up to 40 kilowatts where I can use it as usual.
If you know how to handle it, please let me know.
The alarm listed below goes off when I remove water.
(Alarm)
1. When I warm the device before start of removing the water, output of lamp goes up only to 20 kilowatts, and the alarm goes off.
2. After the alarm goes off, the output of the lamp is shown "0 kilowatt". Then I click "end" and stop operation.
If I repeat above 2 to 3 times, the output of the lamp goes up to 40 kilowatts where I can use it as usual.
If you know how to handle it, please let me know.
評価
52
翻訳 / 英語
- 2018/06/12 13:13:30に投稿されました
There is something wrong happening with the equipment.
The following alarm goes off when we drain the water.
(Alarm)
The defect situation：
1. As the warm up operation before the drainage starts, the output for the lamps only goes up till 20kw and the alarm goes off.
2. The lamp output gets shown as 0kw when the alarm goes off so you click the “finish” and stop the operation.
After repeating this process twice or three times the lamp output goes up to 40kw it starts operating normally.
Please let us know if there is anything that might help.
The following alarm goes off when we drain the water.
(Alarm)
The defect situation：
1. As the warm up operation before the drainage starts, the output for the lamps only goes up till 20kw and the alarm goes off.
2. The lamp output gets shown as 0kw when the alarm goes off so you click the “finish” and stop the operation.
After repeating this process twice or three times the lamp output goes up to 40kw it starts operating normally.
Please let us know if there is anything that might help.
評価
52
翻訳 / 英語
- 2018/06/12 13:09:46に投稿されました
There is a malfunction with the device.
When the water is discharged, the following alarm is raised.
(alarm)
Malfunction situation:
1. At the time when the device is warmed up before the water discharge, the lamp's output cannot go beyond 20kw and the alarm sounds.
2. After the alarm is raised, the lamp's output shows 0kw. When the "end" button is clicked, the operation is terminated.
After doing this for two to three times, the lamp's output goes up to 40kw before it can be used normally again.
Can you please let me know how to deal with this problem, if any?
When the water is discharged, the following alarm is raised.
(alarm)
Malfunction situation:
1. At the time when the device is warmed up before the water discharge, the lamp's output cannot go beyond 20kw and the alarm sounds.
2. After the alarm is raised, the lamp's output shows 0kw. When the "end" button is clicked, the operation is terminated.
After doing this for two to three times, the lamp's output goes up to 40kw before it can be used normally again.
Can you please let me know how to deal with this problem, if any?
![[削除済みユーザ]](https://secure.gravatar.com/avatar/695023b4efd563721d13716b1457bc73.png?d=identicon&mode=crop&r=PG&s=42)
評価
50
翻訳 / 英語
- 2018/06/12 13:14:04に投稿されました
There is malfunction in the equipment.
The alarm goes on when discharging water as below.
(alarm)
Details of malfunction:
1) When start warming up before discharging water, lamp for power generation goes up only to 20kw and alarm goes on.
2) After alarm, click on to turn off the operation when lamp goes down to 40kw.
As you repeat this operation 2, 3 times, power generation of lamp goes up to 40kw, and starts operation as usual.
Please let know if there is way to fix this.
The alarm goes on when discharging water as below.
(alarm)
Details of malfunction:
1) When start warming up before discharging water, lamp for power generation goes up only to 20kw and alarm goes on.
2) After alarm, click on to turn off the operation when lamp goes down to 40kw.
As you repeat this operation 2, 3 times, power generation of lamp goes up to 40kw, and starts operation as usual.
Please let know if there is way to fix this.
評価
50
翻訳 / 英語
- 2018/06/12 13:22:28に投稿されました
Something is wrong with the equipment.
Alarms when draining.
(Alarm)
Malfunction:
1. When idling before start draining, the output of the lamp goes only up to 20 kilowatts and starts alerting.
2. After the alert, it shows that the output of the lamp is 0 kilowatt, so I terminate by clicking "end" button.
After repeating this two or three times, the output of the lamp goes up to 40 kilowatts and I am able to use normally.
Let me know if there is any way I can deal with this problem.
Alarms when draining.
(Alarm)
Malfunction:
1. When idling before start draining, the output of the lamp goes only up to 20 kilowatts and starts alerting.
2. After the alert, it shows that the output of the lamp is 0 kilowatt, so I terminate by clicking "end" button.
After repeating this two or three times, the output of the lamp goes up to 40 kilowatts and I am able to use normally.
Let me know if there is any way I can deal with this problem.
2)の箇所は40kwではなく0kwに訂正致します。失礼いたしました。