GB10 の中でも、こちらは「初年度モデル」にあたる1977年製
ボディの Fホールから見た Oval Label には GEORGE BENSON の文字の下に SERIAL NO. 031となっています。
この年代物でここまで綺麗なものは生産国の日本でもめったに手に入りません。
早めのご検討をお願い致します。
フロントPU 取付部分であるネックエンドの両側面にネジ穴が４つ空いています。
普段はピックアップ取付後に隠れてしまうので見えることはありませんし、演奏面でも問題無しです。
評価
44
翻訳 / 英語
- 2016/01/11 09:36:17に投稿されました
There are various models among GB10, this one is made in 1977, which is "the first year model".
On Oval Label seen from F hole on the body, "SERIAL NO.031" is written under "GEORGE BENSON".
We seldom see such beautiful vintage guitar, even in country of production, Japan.
Please make your decision as soon as possible.
There are four screw holes on both side of the neck end front where PU is equipped.
But usually they are hidden after the pick up is build on, and they bring no negative impact on playing.
tokyocreatorsさんはこの翻訳を気に入りました
On Oval Label seen from F hole on the body, "SERIAL NO.031" is written under "GEORGE BENSON".
We seldom see such beautiful vintage guitar, even in country of production, Japan.
Please make your decision as soon as possible.
There are four screw holes on both side of the neck end front where PU is equipped.
But usually they are hidden after the pick up is build on, and they bring no negative impact on playing.
評価
50
翻訳 / 英語
- 2016/01/11 09:36:55に投稿されました
Among GB10, this was produced in 1977 and it is the "first year model."
At oval label that we see from F hall of the body, serial number 031 is listed under "George Benson."
We can hardly obtain the item produced in this year, which is as beautiful as this one, even in Japan where it is produced.
We appreciate if you consider it earlier.
There are 4 holes for screw at both sides of neck end, where front PU is set.
As it is hidden after pick up is set usually, we cannot see it. We do not have a problem in performing, either.
At oval label that we see from F hall of the body, serial number 031 is listed under "George Benson."
We can hardly obtain the item produced in this year, which is as beautiful as this one, even in Japan where it is produced.
We appreciate if you consider it earlier.
There are 4 holes for screw at both sides of neck end, where front PU is set.
As it is hidden after pick up is set usually, we cannot see it. We do not have a problem in performing, either.
評価
52
翻訳 / 英語
- 2016/01/11 09:56:18に投稿されました
Among GB10s, this one was made in 1977, which is "the first year model."
On Oval Label which I see from the F hole of the body reads SERIAL NO. 031 under the letter of GEORGE BENSON.
Such a beautiful one of the antiques is rarely available even in Japan, the original producer country.
I would like your early examination and decision.
Four screw holes are seen on both sides of the neck end that holds the front PU.
Because they are usually covered under the pickup after it is installed I do not see them, and make no problem in playing.
On Oval Label which I see from the F hole of the body reads SERIAL NO. 031 under the letter of GEORGE BENSON.
Such a beautiful one of the antiques is rarely available even in Japan, the original producer country.
I would like your early examination and decision.
Four screw holes are seen on both sides of the neck end that holds the front PU.
Because they are usually covered under the pickup after it is installed I do not see them, and make no problem in playing.
