私は彼がいう事が正しいかどうかをお伝えすることはできません。
ただ、Fender USAとFender Japanではインチとミリメーターで規格がちがうので
ネジ穴の位置が異なるはずです。
確実なのはこのギターがお客様の手元に届いたらそのサイズを実測してから
ピックガードを発注する事をお勧めします。
日本ではミントグリーンのピックガード自体がとても珍しいのでどうしても割高になります。
もし日本で作れば受注生産になり$100~$150で納期は1~2ヶ月はかかると思います。
翻訳 / 英語
- 2014/05/04 17:05:19に投稿されました
I can't tell whether what he says is correct.
However, because of the different standards between millimeters in Fender Japan and inches in Fender USA, the position of the screw hole should be different.
I advise you to measure the size of this guitar after it is delivered to you and order a pick guard to make it assure.
It will be really expensive because pick guard itself is very rare in Japan.
I think that it will cost $ 100 to $ 150 due to build-to-order manufacturing and delivery time will take 1-2 months at if it is made in Japan.
However, because of the different standards between millimeters in Fender Japan and inches in Fender USA, the position of the screw hole should be different.
I advise you to measure the size of this guitar after it is delivered to you and order a pick guard to make it assure.
It will be really expensive because pick guard itself is very rare in Japan.
I think that it will cost $ 100 to $ 150 due to build-to-order manufacturing and delivery time will take 1-2 months at if it is made in Japan.
翻訳 / 英語
- 2014/05/04 16:58:10に投稿されました
I cannot tell you whether or not what he says is right.
However, there is a difference between Fender USA and Japan regarding the measurements. Fender USA uses inch, and Japan uses centimeter, so the location of screw holes might differ.
The safest way is that you order a pickguard after you receive the guitar and measure the size.
In Japan, the mint green color pick is rare, so it is relatively expensive. If you prefer the one made in Japan, we will make it after we get your order. I think it will cost $100 - 150 and takes a couple of months.
However, there is a difference between Fender USA and Japan regarding the measurements. Fender USA uses inch, and Japan uses centimeter, so the location of screw holes might differ.
The safest way is that you order a pickguard after you receive the guitar and measure the size.
In Japan, the mint green color pick is rare, so it is relatively expensive. If you prefer the one made in Japan, we will make it after we get your order. I think it will cost $100 - 150 and takes a couple of months.
★★★★☆ 4.0/2
翻訳 / 英語
- 2014/05/04 17:13:42に投稿されました
I can not tell you what he said is right or wrong.
However, position of the screw hole should be different, as the different standards in millimeters and inches in Fender USA and Fender Japan.
I recommend you to purchase a pickguard after you have measured the size of guitar arrives for sure.
The mint green pickguard is really expensive as it is rare in Japan.
I think it will cost $100-$150 for 1-2 month if it is produced on order in Japan
However, position of the screw hole should be different, as the different standards in millimeters and inches in Fender USA and Fender Japan.
I recommend you to purchase a pickguard after you have measured the size of guitar arrives for sure.
The mint green pickguard is really expensive as it is rare in Japan.
I think it will cost $100-$150 for 1-2 month if it is produced on order in Japan