現在試験結果の最終確認をしています。
前に同じ質問をしているかもしれませんが、下記について確認させてください。
1. 2020年の陸上試験のUVIの値が1000 W/m2を超えていますが、これは試験水の水質がクリアであり、UVIの値が大きくなっても流量が制御されるため、システム上問題はないということでよろしいでしょうか？
2. LowモードとHighモードの切り替えによって、UVランプ自体の出力が変更されるのでしょうか？
評価
50
翻訳 / 英語
- 2021/10/05 15:48:12に投稿されました
We are now doing the final confirmation of the test result.
I might ask you the same question before, but please let me confirm the below.
1. The value of UVI on land test in 2020 is over 1000 W/m2.
Can I understand that it is no problem on the system since the water quality of the test water is clear and flow quantity is controlled even though UVI value becomes large?
2. Will the output of UV lamp itself change by switching between Low mode and High mode?
I might ask you the same question before, but please let me confirm the below.
1. The value of UVI on land test in 2020 is over 1000 W/m2.
Can I understand that it is no problem on the system since the water quality of the test water is clear and flow quantity is controlled even though UVI value becomes large?
2. Will the output of UV lamp itself change by switching between Low mode and High mode?
評価
44
翻訳 / 英語
- 2021/10/05 15:45:22に投稿されました
The final confirmation of the test results is now in progress.
I may have asked the same question before, but I would like to confirm the following.
1.In the 2020 onshore test, the UVI value exceeded 1000 W/m2. Is this correct to understand that the water quality of the test water is clear and the flow rate is controlled even if the UVI value increases?
2. Does switching between Low and High modes change the output of the UV lamp itself?
I may have asked the same question before, but I would like to confirm the following.
1.In the 2020 onshore test, the UVI value exceeded 1000 W/m2. Is this correct to understand that the water quality of the test water is clear and the flow rate is controlled even if the UVI value increases?
2. Does switching between Low and High modes change the output of the UV lamp itself?
評価
50
翻訳 / 英語
- 2021/10/05 15:48:30に投稿されました
I am making a final check of the test result.
I might have asked the same question before, but please let me check the following.
1. UVI value of the truck test of 2020 exceeds W/m2. May I understand that there is no problem at the system since water quality of the test water is clear and volume of the flow is controlled even if the value is large?
2. Is output of UV lamp changed if low mode and high mode are switched?
I might have asked the same question before, but please let me check the following.
1. UVI value of the truck test of 2020 exceeds W/m2. May I understand that there is no problem at the system since water quality of the test water is clear and volume of the flow is controlled even if the value is large?
2. Is output of UV lamp changed if low mode and high mode are switched?
評価
52
翻訳 / 英語
- 2021/10/05 15:54:38に投稿されました
We are now conducting the final check-up on the test result. Just let me confirm for the following.
Despite the same questions that seem to make.
1. Although the value of UVI on the ground test exceeded 1000 W/m2 in 2020, could I make sure that the quality of water for the test is clear and there is no problem on the system as the flow is controlled even if the value of UVI becomes greater?
2. By switching between the Low mode and High mode, the output of the UV lamp itself is changed, right?
Despite the same questions that seem to make.
1. Although the value of UVI on the ground test exceeded 1000 W/m2 in 2020, could I make sure that the quality of water for the test is clear and there is no problem on the system as the flow is controlled even if the value of UVI becomes greater?
2. By switching between the Low mode and High mode, the output of the UV lamp itself is changed, right?
