inletの圧力がoutletの圧力より高いということはありえないと思います。
笑い話ですが、日本でも圧力計がinletとoutlet逆に付いていた客先がいましたので、
無いとは思いますが、お客様に確認いただければと思います。
または、圧力計自体に不備があるかだと思います。
製造した樹脂に問題がないのであれば、機器自体に問題は無いのだと思います。
お客様に聞きづらいとは思いますが、圧力計の設置位置について確認してみてください。
念の為に確認ですが、機器を使用している樹脂はAでしたよね？
評価
44
翻訳 / 英語
- 2021/03/24 15:40:40に投稿されました
I don't think inlet pressure is higher than outlet pressure.
It is just a joke, but, in Japan, one of the customers attached pressure gauge inlet and outlet other way round, so I would like you to confirm with the customer just in case.
Or, the pressure gauge itself has some problem.
If the manufactured regin is fine, then the equipment is OK.
I am afraid you will have difficulty to ask your customer, but please ask the customer about the position of the pressur gauge.
Just to make sure, the regin using the equipment is A, right?
It is just a joke, but, in Japan, one of the customers attached pressure gauge inlet and outlet other way round, so I would like you to confirm with the customer just in case.
Or, the pressure gauge itself has some problem.
If the manufactured regin is fine, then the equipment is OK.
I am afraid you will have difficulty to ask your customer, but please ask the customer about the position of the pressur gauge.
Just to make sure, the regin using the equipment is A, right?
評価
50
翻訳 / 英語
- 2021/03/24 15:44:16に投稿されました
It is impossible case that the pressure of inlet is higher than outlet one.
It is a kind of joke, but there was a customer in Japan that made a mistake to attach pressure gauge inlet and outlet reversely.
Please confirm about it to customer, maybe it is not probably.
Or may have something wrong about pressure gauge itself.
If there is no problem of manufactured resin, I think there is no problem of equipment itself.
Maybe it is difficult to ask to customer, please confirm the position of pressure gauge on the equipment.
I want to confirm to make sure, resin which is using for equipment is A?
It is a kind of joke, but there was a customer in Japan that made a mistake to attach pressure gauge inlet and outlet reversely.
Please confirm about it to customer, maybe it is not probably.
Or may have something wrong about pressure gauge itself.
If there is no problem of manufactured resin, I think there is no problem of equipment itself.
Maybe it is difficult to ask to customer, please confirm the position of pressure gauge on the equipment.
I want to confirm to make sure, resin which is using for equipment is A?
評価
52
翻訳 / 英語
- 2021/03/24 15:45:46に投稿されました
I don't think it is possible for the pressure at the inlet to be higher than the pressure at the outlet.
It's a funny story, but there was a customer in Japan who had a pressure gauge attached to both inlet and outlet.
I don't think this is the case, but I hope the customer will confirm that.
I think the pressure gauge itself may be defective.
If there is no problem with the resin used to manufacture the pressure gauge, then there is no problem with the device itself.
I know it is hard to ask the customer, but please check the installation position of the pressure gauge.
Just to be sure, the resin used for the equipment was A, right?
It's a funny story, but there was a customer in Japan who had a pressure gauge attached to both inlet and outlet.
I don't think this is the case, but I hope the customer will confirm that.
I think the pressure gauge itself may be defective.
If there is no problem with the resin used to manufacture the pressure gauge, then there is no problem with the device itself.
I know it is hard to ask the customer, but please check the installation position of the pressure gauge.
Just to be sure, the resin used for the equipment was A, right?
