分解の手順は以下の通りです。
1.前後の配管を外す（動画では実施済み）
2.ヒータを外す（ただし、ヒータを外す前に容器を温めておく必要はある）
3.六角穴付きボルトを外し、容器とアウトレットカバーとインレットカバーに分解する
4.溶剤・熱処理などで付着している樹脂を除去する
5.エレメントを外す
現状ではエレメントが外れているようですので、エレメントが容器内で浮いている状態となります。
次工程は容器の分解になるかと思いますが、その際にエレメントを傷つけないように注意してください。
評価
52
翻訳 / 英語
- 2020/10/21 16:30:36に投稿されました
The disassembling is for the following.
1. Remove the tubes of the front and back. (It was conducted on the video.)
2. Remove the heater. (The container should be heated before removing the heater.)
3. Remove the hexagon socket head bolt, it should be disassembled to the container, outlet cover, and inlet cover respectively.
4. Remove the resin which are formed because of solvent or hear treatment.
5. Remove the element.
At the moment, the element stays removed seemingly. The element is floating in the container.
As the next step will be disassembling the container, be sure to use caution not to damage to the element.
1. Remove the tubes of the front and back. (It was conducted on the video.)
2. Remove the heater. (The container should be heated before removing the heater.)
3. Remove the hexagon socket head bolt, it should be disassembled to the container, outlet cover, and inlet cover respectively.
4. Remove the resin which are formed because of solvent or hear treatment.
5. Remove the element.
At the moment, the element stays removed seemingly. The element is floating in the container.
As the next step will be disassembling the container, be sure to use caution not to damage to the element.
評価
44
翻訳 / 英語
- 2020/10/21 16:21:37に投稿されました
The steps for disassembly are as follows.
1. Remove the front and rear piping (already done in the video)
2. Remove the heater (but the container needs to be warmed up before removing the heater)
3. Remove the hexagon socket bolt and disassemble the container, outlet cover and inlet cover.
4. Remove resin adhered by solvents, heat treatment, etc.
5. Remove the element.
Since the element seems to be detached at this point, the element is floating in the container.
The next step is to disassemble the container, but be careful not to damage the element.
takatoshiさんはこの翻訳を気に入りました
1. Remove the front and rear piping (already done in the video)
2. Remove the heater (but the container needs to be warmed up before removing the heater)
3. Remove the hexagon socket bolt and disassemble the container, outlet cover and inlet cover.
4. Remove resin adhered by solvents, heat treatment, etc.
5. Remove the element.
Since the element seems to be detached at this point, the element is floating in the container.
The next step is to disassemble the container, but be careful not to damage the element.
評価
52
翻訳 / 英語
- 2020/10/21 16:23:17に投稿されました
Disassemble step as per below
1. Remove the front and rear piping (Done in the video)
2. Remove the heater (but it is necessary to keep the container warm before removing the heater)
3. Remove the bolt with hexagonal holes and disassemble it into containers and outlet covers and inlet covers.
4. Remove resin adhering to solvents, heat treatment, etc.
5. Remove the element
At present, the element may be detached, so the element is floating in the container.
I think the next step will be to disassemble the container, but be careful not to damage the elements.
1. Remove the front and rear piping (Done in the video)
2. Remove the heater (but it is necessary to keep the container warm before removing the heater)
3. Remove the bolt with hexagonal holes and disassemble it into containers and outlet covers and inlet covers.
4. Remove resin adhering to solvents, heat treatment, etc.
5. Remove the element
At present, the element may be detached, so the element is floating in the container.
I think the next step will be to disassemble the container, but be careful not to damage the elements.
評価
50
翻訳 / 英語
- 2020/10/21 16:23:07に投稿されました
The disassembly procedure is as follows.
1. Remove the front and rear pipes (already done in the video)
2. Remove the heater (however, the container must be warmed before removing the heater)
3. Remove the hexagon socket head cap screw and disassemble into the container, outlet cover and inlet cover.
4. Remove the adhering resin by solvent / heat treatment, etc.
5. Remove the element
At present, the element seems to have come off, so the element is floating inside the container.
I think the next process will be disassembling the container, but be careful not to damage the element at that time.
takatoshiさんはこの翻訳を気に入りました
1. Remove the front and rear pipes (already done in the video)
2. Remove the heater (however, the container must be warmed before removing the heater)
3. Remove the hexagon socket head cap screw and disassemble into the container, outlet cover and inlet cover.
4. Remove the adhering resin by solvent / heat treatment, etc.
5. Remove the element
At present, the element seems to have come off, so the element is floating inside the container.
I think the next process will be disassembling the container, but be careful not to damage the element at that time.
