基準は目視確認です。限度見本と見比べるのみで、数値の基準はありません。
乾燥は温度、時間で管理していますが、乾燥が完了しているかの確認基準はありません。
添付いただいたグラフの縦軸は入口圧でしょうか？
また、運転条件は開示できますでしょうか？
エレメントの切断についてですが、Aで熱処理した後でないとセンターポールからエレメントを外せないので、
樹脂が中に入った状態でエレメントを切断することはできません。
仮に切断できたとしても、中の樹脂の状態から我々は何も判断できません。
評価
50
翻訳 / 英語
- 2018/05/16 17:38:06に投稿されました
Visually confirm the standard. There is no numerical standard as it only required to visually compare with the limit sample.
Although the dryness is controlled by temperature and time, there is no confirmation standard to see if the dryness is complete or not.
Is the vertical axis in the attached graph an inlet pressure?
Also, can the operation condition be disclosed?
As for the element disconnection, since the element cannot be removed from the center pole without applying heat process with A, it cannot be disconnected while resin is kept inside.
Even though it could be disconnected, there is nothing we can judge from the condition of the resin inside.
Although the dryness is controlled by temperature and time, there is no confirmation standard to see if the dryness is complete or not.
Is the vertical axis in the attached graph an inlet pressure?
Also, can the operation condition be disclosed?
As for the element disconnection, since the element cannot be removed from the center pole without applying heat process with A, it cannot be disconnected while resin is kept inside.
Even though it could be disconnected, there is nothing we can judge from the condition of the resin inside.
評価
50
翻訳 / 英語
- 2018/05/16 17:39:08に投稿されました
Standard is by visible check. We only compare with measure sample and there is no value of standard.
Dryness is controlled by temperature and time, but there is no checking standard whether dry process is completed.
Axis of attached graph is entrance pressure?
Or can you disclose running condition?
Regarding element cut, element can be removed from center pole only after heat treatment at A, and it is not able to cut element when resin is inside.
Even though we can cut, we cannot judge anything from the condition of inside resin.
Dryness is controlled by temperature and time, but there is no checking standard whether dry process is completed.
Axis of attached graph is entrance pressure?
Or can you disclose running condition?
Regarding element cut, element can be removed from center pole only after heat treatment at A, and it is not able to cut element when resin is inside.
Even though we can cut, we cannot judge anything from the condition of inside resin.
評価
52
翻訳 / 英語
- 2018/05/16 17:33:57に投稿されました
The standard is to do a visual confirmation. As this only involves comparing with the criteria sample, there are no numeric standards.
Although the drying process is managed through controlling temperature and time, there is no confirmation standard with regard to checking whether the drying has been completed.
With regard to the graph sent as attached, is the vertical axis reflecting the input pressure?
In addition, is it possible to disclose the operating condition?
With regard to the cutting of the element, A has to be subjected to heat treatment before the center ball can be removed from the element. Under the condition where the resin is inside, it would be impossible to cut the element. Even if we manage to cut it, we cannot determine the condition of the resin within.
Although the drying process is managed through controlling temperature and time, there is no confirmation standard with regard to checking whether the drying has been completed.
With regard to the graph sent as attached, is the vertical axis reflecting the input pressure?
In addition, is it possible to disclose the operating condition?
With regard to the cutting of the element, A has to be subjected to heat treatment before the center ball can be removed from the element. Under the condition where the resin is inside, it would be impossible to cut the element. Even if we manage to cut it, we cannot determine the condition of the resin within.
訂正があります: center ball -> center pole