ペンチでクランプを緩め正しい位置に修正する
カンコツ
最初にホース先端部をパイプの端角に被せて押込む
パイプを手で固定し、ホースを左右に捩じりながら差し込む
ホースの先端から差込み代（25㎜）付近を持ち、挿入した時の指の感触（膨らむ感）まで差し込む
木型のチェックプレートを当てて、ホースの姿勢とクランプの向き、位置を確認する（工程内検査）
ホース挿入前にクランプを通しておく
赤い止め具が付いていることを確認する
クランプでホース表面に傷をつけないこと
インパネ内部の搭載状態
ヒーターの故障モード
評価
47
翻訳 / 英語
- 2015/03/11 16:17:57に投稿されました
Use pliers to release the clamp & adjust it in right position.
Works only learned through actual experience.
Using the hose's tip to cover the edge-corner of pipe first , then shoving it onto the pipe.
Handling the pipe , then shoving the hose on with torsioning.
Handling above 25mm spare using to shoving from the hose's tip , and shoving it on until feeling swell from fingers.
Apply the wooden check plate to checking the posture of hose & the direction of clamp.（Process inspection）
Keep thorough the clamp before insert the hose.
Be sure the stopper with red - colored was be fitted.
Do not hurt the surface of hose by clamp.
Mounting state inside the Instrument Panel .
Breakdown status of heater.
Works only learned through actual experience.
Using the hose's tip to cover the edge-corner of pipe first , then shoving it onto the pipe.
Handling the pipe , then shoving the hose on with torsioning.
Handling above 25mm spare using to shoving from the hose's tip , and shoving it on until feeling swell from fingers.
Apply the wooden check plate to checking the posture of hose & the direction of clamp.（Process inspection）
Keep thorough the clamp before insert the hose.
Be sure the stopper with red - colored was be fitted.
Do not hurt the surface of hose by clamp.
Mounting state inside the Instrument Panel .
Breakdown status of heater.
評価
50
翻訳 / 英語
- 2015/03/10 23:08:17に投稿されました
Adjust to a right position by loosening the clamp using plier.
Based on feeling.
Firstly, insert and cover the end of the hose into the tip of the pipe.
Hold the pipe using hand while insert the hose by twisting it to the left and right.
Insert the hose until about 25mm from the hose tip, and feel by hand that the hose is swollen.
Check hose position and clamp direction and position by touching it to wooden check plate (process inspection).
Before insert the hose, pass through the clamp first.
Confirm that red stopper jig is attached.
No scratch on hose surface by clamping.
Mounted condition of internal part of instrument panel.
Failure mode of heater.
m20368さんはこの翻訳を気に入りました
Based on feeling.
Firstly, insert and cover the end of the hose into the tip of the pipe.
Hold the pipe using hand while insert the hose by twisting it to the left and right.
Insert the hose until about 25mm from the hose tip, and feel by hand that the hose is swollen.
Check hose position and clamp direction and position by touching it to wooden check plate (process inspection).
Before insert the hose, pass through the clamp first.
Confirm that red stopper jig is attached.
No scratch on hose surface by clamping.
Mounted condition of internal part of instrument panel.
Failure mode of heater.
評価
44
翻訳 / 英語
Know-how to unscrew the cramp and fix it to right place.
Ｐｕsh and stuff the top edge of the hose with covering it at the corner edge of the pipe.
Ｆix the pipe with a hand, plug the hose into the pipe with screwing the hose from left to right,
Hold the area around the plug-in hole from top edge of the hose[25mm], plug it into the point that you can feel your finger touch[ expansion feeling ].
Check the stance of the hose and the direction and the position of the cramp with screening by the wooden check plate.
Stick the cramp forecast before plugging the hose.
Check built in red stopper parts.
Don't hurt the surface of hose by the cramp.
Trouble mode of heater.
- 2015/03/11 16:02:00に投稿されました
Know-how to unscrew the cramp and fix it to right place.
Ｐｕsh and stuff the top edge of the hose with covering it at the corner edge of the pipe.
Ｆix the pipe with a hand, plug the hose into the pipe with screwing the hose from left to right,
Hold the area around the plug-in hole from top edge of the hose[25mm], plug it into the point that you can feel your finger touch[ expansion feeling ].
Check the stance of the hose and the direction and the position of the cramp with screening by the wooden check plate.
Stick the cramp forecast before plugging the hose.
Check built in red stopper parts.
Don't hurt the surface of hose by the cramp.
Trouble mode of heater.
★★☆☆☆ 2.0/1
