ついにArduinoがMicroUSBコネクタを持った!
コネクタの突起はカットします
30W以上のハンダごてと吸取線でArduino側のハンダを取除きます
この写真くらい吸取ればOK
基板をコネクタの端子部分に強く押し付けます
隙間がこのくらいならOK
多めのハンダ付けします。5秒以上加熱してハンダを流し込んでください
完成
ちゃんと認識されています
これで、あの大きなUSBケーブルも不要になりますね!
LPC利用時
激安$3.00でmbedが何個でも作れる! (LPC810なら$2.50)
評価
52
翻訳 / 英語
- 2014/11/29 12:54:30に投稿されました
Now MicroUSB connector is availabel for Arduino!
Cut off the nubs on the connector.
Take away the solder on the Arduino board side using the soldering iron (30W or above) and the solder wick.
OK if you take away this much.
Press the base strongly to the terminal part of the connector.
OK if the gap becomes about this much.
Solder rather fully. Heat it more than five seconds and pour the solder.
Completed.
All are recognized properly.
Now, you don't need the big USB cable!
Pictures with the LPC use
You can make as many mbed as you like at super-discount $ 3.00 (LPC810 is $ 2.50)!
will2ttさんはこの翻訳を気に入りました
Cut off the nubs on the connector.
Take away the solder on the Arduino board side using the soldering iron (30W or above) and the solder wick.
OK if you take away this much.
Press the base strongly to the terminal part of the connector.
OK if the gap becomes about this much.
Solder rather fully. Heat it more than five seconds and pour the solder.
Completed.
All are recognized properly.
Now, you don't need the big USB cable!
Pictures with the LPC use
You can make as many mbed as you like at super-discount $ 3.00 (LPC810 is $ 2.50)!
評価
46
翻訳 / 英語
- 2014/11/29 13:29:38に投稿されました
Finally,Arduino had MicroUSD!
Cut the projection of the connector.
Remove the solder in the side of Arduino with the soldering iron whose power is more than 30W and the solder wick.
If you can suck up the solder like this picture,it is OK.
Press the foundation against the part of the connector terminal strongly.
If that clearance is like this picture ,it is OK,
Do soldering somewhat larger quantity.
Add the heat more than 5 seconds and pour the solder.
Completion
It can recongnize it without mistake.
With this method,you don't need to use kind of big USB cable.
If you use LPC:
You can make many mbeds even thouh how many they are with bargain price $3.00.
(If you use LPC810 ,the price is $2.50)
will2ttさんはこの翻訳を気に入りました
Cut the projection of the connector.
Remove the solder in the side of Arduino with the soldering iron whose power is more than 30W and the solder wick.
If you can suck up the solder like this picture,it is OK.
Press the foundation against the part of the connector terminal strongly.
If that clearance is like this picture ,it is OK,
Do soldering somewhat larger quantity.
Add the heat more than 5 seconds and pour the solder.
Completion
It can recongnize it without mistake.
With this method,you don't need to use kind of big USB cable.
If you use LPC:
You can make many mbeds even thouh how many they are with bargain price $3.00.
(If you use LPC810 ,the price is $2.50)
