工程管理明細表からの規格に対する注意事項
ｺｲﾙ交換時に、指差し確認にてチェックすること
メタルチェッカーにてチェックすること
全数材料を立て、目視チェックすること
先端バリ0.3㎜以下、内径バリ0.1㎜以下
必要に応じて準備する
現在加工中の切断長にプラス１００ｍｍを入力して２本切断後赤箱へ廃却すること
但し､汎用合理化用（2013年8月現在設置工場Ａ）は、3㎜で管理
始業点検
日常保全チェックｼｰﾄに基づき、フック・吊り具の状態及びホイストクレーンの動作の確認を実施する。
評価
52
翻訳 / 英語
- 2015/05/22 08:11:10に投稿されました
Precautions to the standard from the process control line table
Check by "pointing and calling" at the moment of changing the coil.
Check with a metal checker.
Check with eyes setting up all the materials
The terminal burr - under 0.3 mm the inside diameter burr - under 0.1mm
Prepare if necessary
Add 100mm to the currenly processing cutting length and enter. After cutting 2 pieces, discard them to the red box.
However, control with 3mm as for pieces for general use or for streamlining( As of August 2013, installed factory: A)
Pre-operation inspection
Based on daily the maintenance check sheet,verify the conditions of hooks and slings and conduct operation confirmation tests of hoist cranes.
mgbarnsさんはこの翻訳を気に入りました
Check by "pointing and calling" at the moment of changing the coil.
Check with a metal checker.
Check with eyes setting up all the materials
The terminal burr - under 0.3 mm the inside diameter burr - under 0.1mm
Prepare if necessary
Add 100mm to the currenly processing cutting length and enter. After cutting 2 pieces, discard them to the red box.
However, control with 3mm as for pieces for general use or for streamlining( As of August 2013, installed factory: A)
Pre-operation inspection
Based on daily the maintenance check sheet,verify the conditions of hooks and slings and conduct operation confirmation tests of hoist cranes.
評価
50
翻訳 / 英語
- 2015/05/22 08:29:31に投稿されました
Notes for standards on process management table
When replacing coils, perform finger pointing check
Check should use a metal checker
Stand all materials and perform visual check
A burr on edge should be no larger than 0.3mm, a burr on inner diameter should be no larger than 0.1mm
Make preparation per necessity
Input 100mm addition on top of the cutting length of the one under process and discard unneeded parts into the red box after cut off 2 rolls
However, the one for general purpose improvement (currently installed at factory A as of August 2013), manage at 3mm
Inspection at begging of operation
Based on daily safety check sheet, check the status of hooks and lifters, as well as the operation of hoist cranes
When replacing coils, perform finger pointing check
Check should use a metal checker
Stand all materials and perform visual check
A burr on edge should be no larger than 0.3mm, a burr on inner diameter should be no larger than 0.1mm
Make preparation per necessity
Input 100mm addition on top of the cutting length of the one under process and discard unneeded parts into the red box after cut off 2 rolls
However, the one for general purpose improvement (currently installed at factory A as of August 2013), manage at 3mm
Inspection at begging of operation
Based on daily safety check sheet, check the status of hooks and lifters, as well as the operation of hoist cranes
お手数おかけしました