恐らく〇〇社はハウジングに傷が付いている状態でAを使用していたと考えております。
ですので、傷の修正をせずにAをアッセンブリーするのも1つの方法ですが、どういたしますか？
また、プラグボルトは最初からなめている状態でした。
図面に不具合があった場所を記しましたので、確認下さい。
また、傷の付いた部品の写真も添付にてお送り致します。
サンプル採取のタイミングについては、押出機安定直後、50Kg流した時点、100Kg流した時点の
3回でサンプルを取っています。
評価
50
翻訳 / 英語
- 2018/03/10 19:39:15に投稿されました
I suppose that ○○ used A when its housing is damaged.
Therefore, I suggest that assembling A without fixing the damage is one of the ways. How do you think about it?
In addition, the plug bolt was flattened from the beginning.
I pointed the parts which have flaws in the diagram, so please confirm.
Additionally, I will send the photograph of the damaged parts.
As for the time of sampling, we have sampled three times: directly after poising the extruder, when pouring 50 kilograms, and when pouring 100 kilograms.
Therefore, I suggest that assembling A without fixing the damage is one of the ways. How do you think about it?
In addition, the plug bolt was flattened from the beginning.
I pointed the parts which have flaws in the diagram, so please confirm.
Additionally, I will send the photograph of the damaged parts.
As for the time of sampling, we have sampled three times: directly after poising the extruder, when pouring 50 kilograms, and when pouring 100 kilograms.
評価
50
翻訳 / 英語
- 2018/03/10 19:52:07に投稿されました
I think A may be used with housing being scratched by ○○ corporation.
Therefore, we can assemble without restoring scratch, it is one of ways, How is it?
Also, The screwhread of plug bolt was broken at the beginning.
We show where wrong is on a plan, please confirm it.
Also, We'll attach the photo of parts being scratched to this email.
Regarding when we take samples, it is three times in total as extruding machine is steady, 50 kilo is dashed, and 50 kilo is dashed.
Therefore, we can assemble without restoring scratch, it is one of ways, How is it?
Also, The screwhread of plug bolt was broken at the beginning.
We show where wrong is on a plan, please confirm it.
Also, We'll attach the photo of parts being scratched to this email.
Regarding when we take samples, it is three times in total as extruding machine is steady, 50 kilo is dashed, and 50 kilo is dashed.
![[削除済みユーザ]](https://secure.gravatar.com/avatar/695023b4efd563721d13716b1457bc73.png?d=identicon&mode=crop&r=PG&s=42)
評価
44
翻訳 / 英語
- 2018/03/10 19:34:14に投稿されました
I think that perhaps ◯◯ company used A with the housing scratched.
So, it is one way to assemble A without correcting scratches, but what do you want to do?
Also, the plug bolt was in a state of being broken from the beginning.
I wrote the place where there was a problem in the drawing, so please check it.
In addition, we will send you the picture of the parts with scratches.
Regarding the timing of sampling, I will take samples in three times as follows;
immediately after stabilization of the extruder, at the time when 50 Kg flowed, and when 100 kg was flowed.
So, it is one way to assemble A without correcting scratches, but what do you want to do?
Also, the plug bolt was in a state of being broken from the beginning.
I wrote the place where there was a problem in the drawing, so please check it.
In addition, we will send you the picture of the parts with scratches.
Regarding the timing of sampling, I will take samples in three times as follows;
immediately after stabilization of the extruder, at the time when 50 Kg flowed, and when 100 kg was flowed.
