原文 / 日本語
コピー
AからBへとアップグレードした際にエラーとなり、
画面にアクセスするとログイン後に、AAAのメッセージ画面が出力され、画面が表示されなくなりました。
そこで、フォーラム（BBB）より同様のメッセージを参照し、再インストールを下記コマンドにて実施
※このコマンド結果は添付ファイルの813行目から1167行目まで
実行が終了し、AAAよりログインするとヘッダー領域、左メニューは表示されるが、画面中央にCCCとだけ表示され操作画面が表示されません。
評価
翻訳 / 英語
- 2011/01/19 13:01:48に投稿されました
The error has occurred when I was upgrading from A to B.
I was accessing to the screen. After I logged in, a message screen with AAA came up and the screen stop displaying.
Therefore, I performed re-installing using the commands below, following the similar massage from the forum (BBB)
* The consequences of the commands will be on line 813 to 1167 on the attached file. After the performance, I logged in through AAA. Although the header area and the left menu were displayed, the control screen was not displayed. Instead, I could see CCC in the middle of the screen.
I was accessing to the screen. After I logged in, a message screen with AAA came up and the screen stop displaying.
Therefore, I performed re-installing using the commands below, following the similar massage from the forum (BBB)
* The consequences of the commands will be on line 813 to 1167 on the attached file. After the performance, I logged in through AAA. Although the header area and the left menu were displayed, the control screen was not displayed. Instead, I could see CCC in the middle of the screen.
評価
51
翻訳 / 英語
- 2011/01/19 13:03:20に投稿されました
I got error when I upgraded from A to B. AAA message appeared after logging in, then the screen became not to show anything.
So I operated re-installation through the command below, reffering the same problems on a forum (BBB). (The result of the command is shown from line 813 to line 1167 of the attatched file)
When the operation finished I logged in from AAA. Then the header region and the menu on the left side are shown but the operation screen is not other than CCC in the center of the screen.
So I operated re-installation through the command below, reffering the same problems on a forum (BBB). (The result of the command is shown from line 813 to line 1167 of the attatched file)
When the operation finished I logged in from AAA. Then the header region and the menu on the left side are shown but the operation screen is not other than CCC in the center of the screen.
評価
翻訳 / 英語
- 2011/01/19 13:51:52に投稿されました
Upgrading the software from A to B, I encounterd the error.
Having accessed the screen and then logged in, it could not show anything with the message of AAA. So, I installed it again by executing the following command while I read the similar message on the forum(BBB).
* The result of this command means from the line 813 to 1167 on the attachement.
After executing the command and then logging in via AAA, the header and menu on the left side had been showned. However, the screen to operate was not shown except for showing CCC on the center of screen.
Having accessed the screen and then logged in, it could not show anything with the message of AAA. So, I installed it again by executing the following command while I read the similar message on the forum(BBB).
* The result of this command means from the line 813 to 1167 on the attachement.
After executing the command and then logging in via AAA, the header and menu on the left side had been showned. However, the screen to operate was not shown except for showing CCC on the center of screen.
